Wutter Vehicle And Details Next18AB – WVD ESU LokSound 5 Micro NEM662 Next18 Adapter Board For Kato F2, F3, F7, FP7, F40PH, P42 – N Scale

Dimensions:  48.4mm x 13.7mm x 2.0mm To Top Of Next18 Connector (Overall height will vary depending on decoder) Notes: 1. This is the same format as Digitrax DN163K0x and TCS K0D8-X series decoders. 2. This product IS NOT recommended for use with E5, E8, E9, PA-1 and PB-1 models.  Significant modification to frame and/or shell would be required for proper fit. The WVD LokSound 5 Micro Adapter Board is a drop-in Next18 decoder adapter board that is designed to be installed in Kato DCC-ready N scale F2, F3, F7, F40PH and P42 locomotives. No more hardwiring and trace cutting needed for sound in these specific units, simply solder your speaker wires and LEDs onto the adapter and go! The adapter was created to simplify the decoder installation process for hobbyists who wish to add sound and/or custom LED lighting to their N scale locomotives as well as UNLOCK the usually unavailable AUX3 and AUX4 functions on the normal LokSound 5 Micro form factor. Excess wiring in your locomotive is eliminated by using the clearly labeled solder pads for connecting a speaker, LEDs, and/or keep alive capacitors to help maintain smooth operation while traversing not-so-clean track or insulated frog turnouts. The WVD LokSound 5 Micro Adapter includes built-in current-limiting resistors for running LEDs directly wired to the board/decoder for up to nine function outputs controlled by the decoder. These functions are: Headlight Taillight Aux 1-7 Additional pads for the U+ and GND rails. In order to use Aux 5-7, wiring directly to the decoder will be required as the cathode pads for AUX5 and AUX6 are on the decoder, and the Logic Level output for AUX7 requires a jumper wire to the specific AUX7 Logic pad on the board. The pickup strips require Kapton tape isolation like every other DCC installation of this board form factor.  It is recommended that Kapton tape be applied over the Next18 connector region onto the mechanism to prevent any accidental disconnections when the shell is reinstalled. A piece of Kapton will be included on the board, and a full wiring diagram for the board will be provided with each purchase. To fit the decoder in a Kato F2, F3, F7 and FP7, nubs on the roof interior will need to be removed in order to fit. Pictures in the instructions show the specific nubs to be removed Supported decoders include the following Electronic Solutions Ulm (ESU) products: LokSound DCC – 58828 (also 58820, 58821, 58823 with removal of existing adapter board) LokSound Multiprotocol – 58818 (also 58810, 58813, 58814, 58816 with removal of existing adapter board) LokPilot DCC – 59828 LokPilot Multiprotocol – 59818 This product can also be used with any NEM662 Next18 compatible decoder including: NCE Next18 DCC Decoder – NEM662 Next18 Integral Connector ZIMO MX618N18 Micro DCC Decoder – NEM662 Next18 Integral Connector ZIMO MX658N18 Micro DCC Sound Decoder – NEM662 Next18 Integral Connector ZIMO MX659N18 Sub-Micro DCC Sound Decoder – NEM662 Next18 Integral Connector Each adapter will be tested for functionality prior to being shipped to the customer. Locomotive not included, decoder not included, speaker not included. Wutter Vehicle and Details N Scale WVD ESU LokSound 5 Micro NEM662 Next18 Adapter Board for Kato F2, F3, F7, FP7, F40PH, P42